VD過程鋼渣混卷行為的水模型

吳華杰; 蔣芳杰; 李巧琦; 張漓; 張永超

doi:10.13374/j.issn2095-9389.2018.s1.021

VD過程鋼渣混卷行為的水模型

doi: 10.13374/j.issn2095-9389.2018.s1.021

1. 北京科技大學鋼鐵共性技術協同創新中心;
2. 北京科技大學工程技術研究院

基金項目:

國家自然科學基金資助項目 (U1660113)

詳細信息

通訊作者:
吳華杰, E-mail:whjyeah@163.com

中圖分類號: TF769.4
計量
- 文章訪問數: 15
- HTML全文瀏覽量: 6
- PDF下載量: 0
- 被引次數: 0
出版歷程
- 收稿日期: 2018-01-10
- 網絡出版日期: 2023-07-18

Physical modeling on the mixing behavior of molten steel and slag in VD process

1. School of Collaborative Innovation Center of Steel Technology,University of Science and Technology Beijing;
2. School of Engineering Research Institute,University of Science and Technology Beijing

摘要

摘要: 通過水模型研究了VD精煉過程的鋼渣混卷行為, 定義了鋼渣臨界半混和臨界全混狀態, 并對不同底吹氣量、真空度、底吹位置下的混合狀態進行了研究;分析了臨界攪拌功率和流場穩定性對混卷行為的影響.結果表明:在實驗條件下, 臨界半混和臨界全混氣量隨著真空度的增大而減小;2/3R雙孔底吹位置的臨界氣量大于2/3R+中心孔底吹位置的;并基于導出的真空度與底吹氣量擬合公式, 外推出真空度為67 Pa時實際生產過程中的臨界氣量;VD過程鋼包流場特性主要受底吹位置影響, 并進一步影響混卷行為, 在穩定性流場中當鋼渣混合達到同一狀態時, 攪拌功率幾乎是定值.
- 真空脫氣 /
- 鋼渣混卷 /
- 攪拌功率 /
- 水模型 /
- 吹氬
Abstract: The mixing behavior of molten steel and slag has an important impact on refining effect in vacuum degassing (VD) process.In the VD refining process, the vacuum condition makes the bottom argon gas agitate the molten steel vigorously, and increase the exposed molten steel area, which not only aggravates the degree of steel slag mixing in the ladle, but also promotes the degassing reaction in molten steel.Moreover, it has an important influence on the desulfurization effect of molten steel.In the actual melting process, the exposed situation of the molten steel can be observed over the slag, but the steel and slag mixing situation in the ladle cannot be observed.Therefore, it has a great practical significance to study the slag mixing behavior in VD refining process under the different process conditions.In the water model experiment, the critical condition of half-mixing and complete-mixing was first defined.And then the impacts of the total blowing flow rate, vacuum degree, and the bottom blowing positions on half-mixing and complete-mixing were discussed.Besides, the effects of critical stirring energy density and stability of flow field on mixing behavior were also analyzed.The results indicate that half-mixing and complete-mixing critical gas flow rate decreases with the increase of vacuum degree in the laboratory condition.And the critical gas flow rate in 2/3R+2/3R is greater than that in 2/3R+center hole.In addition, the fitting formulas of vacuum degree and critical gas flow rate were given.Based on fitting formulas, critical gas flow rate in actual VD process was obtained when vacuum degree was 67 Pa.According to the results, the critical stirring energy density is nearly a constant when the steel-slag mixing reaches the same condition in steady flow field, which indicates that flow character can further influence mixing effect and it is affected by the bottom blowing positions.
- vacuum degassing ladle /
- mixing of molten steel and slag /
- stirring energy density /
- water model /
- argon blowing

HTML全文

參考文獻(16)

[1]	Yu M Q. Practice of denitrification process in 100 t vacuum ladle furnace. Res Iron Steel, 2001, 29 (1) :7 (虞明全. 100 t真空精煉爐脫氮工藝的實踐.鋼鐵研究, 2001, 29 (1) :7)
[2]	Wei J L, Tang P, Wen G H, et al. Study on physical simulation of argon blowing for VD furnace ladle. Res Iron Steel, 2010, 38 (5) :6 (韋江林, 唐萍, 文光華, 等. VD爐鋼包底吹氬的物理模擬.鋼鐵研究, 2010, 38 (5) :6)
[3]	Chen S C, Zhu R, Li J S. Three-phase fluid numerical simulation and water modeling experiment of supersonic oxygen jet impingement on molten bath in EAF. J Iron Steel Res Int, 2014, 21 (6) :589
[4]	Li Y H, Zhao L H, Bao Y P, et al. Flow characteristic of molten steel in slab casting tundishes. J Univ Sci Technol Beijing, 2014, 36 (1) :21 (李怡宏, 趙立華, 包燕平, 等.板坯中間包內鋼液流動特性.北京科技大學學報, 2014, 36 (1) :21)
[5]	Feng J H, Li B B, Wei G Z, et al. Effect of different bottom blowing argon methods on LF refining. J Univ Sci Technol Beijing, 2009, 31 (s1) :7 (馮聚和, 李博斌, 魏國增, 等.鋼包底吹氬方式對LF精煉的影響.北京科技大學學報, 2009, 31 (s1) :7)
[6]	Lu Q T, Yang R G, Wang X H, et al. Water modeling of mold powder entrapment in slab continuous casting mold. Journal of University of Science&Technology Beijing Mineral Metallurgy Material, 2007, 14 (5) :399
[7]	Jakobsson A, Du S, Seetharaman S, et al. Interfacial phenomena in some slag-metal reactions. Metall Mater Trans B, 2000, 31 (5) :973
[8]	Iguchi M, Jin Y, Shimizu T, et al. Model study on the entrapment of mold powder into molten steel. ISIJ Int, 2000, 40 (7) :685
[9]	Iguchi M, Terauchi Y. Karman vortex probe for the detection of molten metal surface flow in low velocity range. ISIJ Int, 2002, 42 (9) :939
[10]	Feldbauer S L. Slag Entrainment in the Mold of a Continuous Caster[Dissertation]. Pittsburgh:Carnegie Mellon University, 1995
[11]	Gao H. Study on Bottom Argon Blowing Process Optimization and Simulation of Cheng-Steel 120 t Ladle Furnace[Dissertation].Beijing:University of Science&Technology Beijing, 2013 (高海.承鋼120 t鋼包底吹氬工藝優化模擬研究[學位論文].北京:北京科技大學, 2013)
[12]	Song F F. Physical and Mathematical Simulation of 160 t Ladle Furnace with Bottom Argon Blowing[Dissertation]. Beijing:University of Science&Technology Beijing, 2012 (宋方方. 160 t鋼包底吹氬工藝物理及數值模擬研究[學位論文].北京:北京科技大學, 2012)
[13]	Ai X G, Bao Y P, Wu H J, et al. A study on water modeling of ladle with bottom argon blowing in critical slag entrapment condition. Special Steel, 2009, 30 (2) :7 (艾新港, 包燕平, 吳華杰, 等.鋼包底吹氬卷渣臨界條件的水模型研究.特殊鋼, 2009, 30 (2) :7)
[14]	Mietz J, Schneider S, Oeters F. Emulsification and mass transfer in ladle metallurgy. Steel Res, 1991, 62 (1) :10
[15]	Oeters F. Metallurgy of Steelmaking. Beijing:Metallurgical Industry Press, 1997 (F.奧特斯.鋼冶金學.北京:冶金工業出版社, 1997)
[16]	Zhu M Y, Xiao Z Q. Mathematical and Physical Simulation in the Steel Refining Process. Beijing:Metallurgical Industry Press, 1998 (朱苗勇, 蕭澤強.鋼的精煉過程數學物理模擬.北京:冶金工業出版社, 1998)