鋼鐵行業燒結煙氣多污染物協同凈化技術研究進展

閆伯駿; 邢奕; 路培; 蘇偉; 姜博; 崔曉旭

doi:10.13374/j.issn2095-9389.2018.07.001

鋼鐵行業燒結煙氣多污染物協同凈化技術研究進展

doi: 10.13374/j.issn2095-9389.2018.07.001

閆伯駿¹,
邢奕^1,2, ,,
路培^1,2,
蘇偉¹,
姜博¹,
崔曉旭¹

1) 北京科技大學能源與環境工程學院, 北京 100083
2) 工業污染物資源化處理北京市重點實驗室, 北京 100083

基金項目:

國家自然科學基金資助項目(U1560110)

中央高校基本科研業務費專項資助項目

國家重點研發計劃資助項目(2017YFC0210300)

詳細信息

中圖分類號: X551
計量
- 文章訪問數: 2291
- HTML全文瀏覽量: 750
- PDF下載量: 101
- 被引次數: 0
出版歷程
- 收稿日期: 2017-07-04

A critical review on the research progress of multi-pollutant collaborative control technologies of sintering flue gas in the iron and steel industry

YAN Bo-jun¹,
XING Yi^{1,2
, ,},
LU Pei^1,2,
SU Wei¹,
JIANG Bo¹,
CUI Xiao-xu¹

1) School of Energy and Environmental Engineering, University of Science and Technology Beijing, Beijing 100083, China
2) Beijing Key Laboratory of Resource-oriented Treatment of Industrial Pollutants, University of Science and Technology Beijing, Beijing 100083, China

摘要

摘要: 基于我國鋼鐵行業燒結煙氣排放標準、排放特征和現行污染物控制技術,分析了國內外先進的多污染物協同控制技術——活性炭(焦)吸附工藝、濕法脫硫除塵+選擇性催化還原協同凈化技術、循環流化床多組分污染物協同凈化工藝、高性能燒結廢氣凈化工藝、新型密相半干法煙氣集成治理技術等工藝的技術思路、特點和存在問題等,并針對鋼鐵行業的實際需求對多污染物協同控制技術的發展提出了建議.
- 鋼鐵行業 /
- 燒結煙氣 /
- 多污染物 /
- 協同凈化 /
- 脫硫 /
- 脫硝
Abstract: The emission of flue gas in the iron and steel industry is high and contains a series of pollutants which that vary widely, especially in sintering process. With the depth of pollution control in China and the increasingly stringent emission standards, the flue gas pollutants of the steel industry require urgent management. At present, the sintering flue gas is mainly treated in the desulfurization and dust removal stages. Moreover, the measures for the management of nitrogen oxides and other pollutants have not yet been fully implemented in China's steel industry. Almost all the air pollution control techniques in the industry are aimed at single pollutant purification, where only few are targeted for multi-pollutant purification. Currently, the single pollutant treatment techniques can be divided into wet, semi-dry, and dry. Among them, the semi-dry and dry methods have gradually attracted much attention because of their high purification efficiency, compactness, and cost-effectiveness. Thus, they have become the main single pollutant treatment technologies for the sintering flue gas emission in the iron and steel industry. The present commonly used multi-pollutant removal technology is a single pollutant purification technique in series. With the increasingly stringent environmental standards in the steel industry, the original pollution control technologies and concepts have shown obvious deficiencies. This has seriously affected the development of China's iron and steel enterprises and smog management process. In addition, the tandem technology of single pollutant removal processes has the disadvantages of large area and high energy consumption. However, the simultaneous purification of multi-pollutants involves a simple process, short process flow, and low operation cost, and thus, it has become a research hotspot. Based on China's iron and steel industry sintering flue gas emission standards, emission characteristics, and current pollutant control technology, the technical ideas, characteristics and existing problems of multi-pollutant-coordinated control technology were analyzed, such as activated carbon adsorption process, LJS-FGD synergy pollutant purification process, MEROS technology, and a new type of dense semi-dry flue gas comprehensive management technology. Finally, some reasonable suggestions were presented for the development of multi-pollutants co-purification technology in the iron and steel industry.
- iron and steel industry /
- sintered flue gas /
- multiple pollutants /
- collaborative purification /
- desulfurization /
- denitrification

HTML全文

參考文獻(21)

[2]	Wang L C, Lee W J, Tsai P J, et al. Emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans from stack flue gases of sinter plants.Chemosphere, 2003, 50(9):1123
[3]	Karademir A, Bakoglu M, Taspinar F, et al.Removal of PCDD/Fs from flue gas by a fixed-bed activated carbon filter in a hazardous waste incinerator. Environ Sci Technol, 2004, 38(4):1201
[4]	Pan J, Zhu D Q, Cui Y, et al. Emission rule of SO₂ in flue gas during sintering. J Central South Univ, 2011, 42(6):1495
[7]	Sun F, Gao J H, Liu X, et al.A systematic investigation of SO₂ removal dynamics by coal-based activated cokes:the synergic enhancement effect of hierarchical pore configuration and gas components. Appl Surf Sci, 2015, 357:1895
[8]	Peng C, Zhang F L, Guo Z C. Gypsum crystallization and potassium chloride regeneration by reaction of calcium chloride solution with potassium sulfate solution or solid.Trans Nonferrous Met Soc China, 2010, 20(4):712
[9]	Peng C, Zhang F L, Cheng Z C. Separation and recovery of potassium chloride from sintering dust of iron making works. ISIJ Int, 2009, 49(5):735
[10]	Tian S D, Hou Y C, Wu W Z, et al. Reversible absorption of SO₂ from simulated flue gas by aqueous calcium lactate solution. J Taiwan Inst Chem Eng, 2015, 54:71
[13]	Hamzehlouyan T, Sampara C S, Li J H, et al.Kinetic study of adsorption and desorption of SO₂ over γ-Al₂O₃ and Pt/γ-Al₂O₃. Appl Catal B:Environ, 2016, 181:587
[14]	Liu Y X, Zhou J F, Wang Q, et al. A novel process for removal of Hg⁰ from flue gas using urea/persulfate activated by high temperature in a spray reactor. Chem Eng Res Des, 2015, 104:828
[15]	Yoosefian M, Zahedi M, Mola A, et al.A DFT comparative study of single and double SO₂ adsorption on Pt-doped and Au-doped single-walled carbon nanotube. Appl Surf Sci, 2015, 349:864
[16]	Ma Z R, Wu X D, Feng Y, et al.Low-temperature SCR activity and SO₂ deactivation mechanism of Ce-modified V₂O₅-WO₃/TiO₂ catalyst. Prog Nat Sci:Mater Int, 2015, 25(4):342
[18]	Fu M F, Li C T, Lu P, et al. A review on selective catalytic reduction of NO_x by supported catalysts at 100-300℃-catalysts, mechanism, kinetics. Catal Sci Technol, 2014, 4:14
[19]	Liang Z Y, Ma X Q, Lin H, et al. The energy consumption and environmental impacts of SCR technology in China. Appl Energy, 2011, 88(4):1120
[20]	Lu X N, Song C Y, Jia S H, et al.Low-temperature selective catalytic reduction of NO_x with NH₃ over cerium and manganese oxides supported on TiO₂-grapheme. Chem Eng J, 2015, 260:776
[21]	Chen W S, Luo J, Qin L B, et al. Selective autocatalytic reduction of NO from sintering flue gas by the hot sintered ore in the presence of NH₃. J Environ Manage, 2015, 164:146
[22]	Zhao Y, Hao R L, Qi M. Integrative process of preoxidation and absorption for simultaneous removal of SO₂, NO and Hg⁰. Chem Eng J, 2015, 269:159
[23]	Ficarella A, Laforgia D. Numerical simulation of flow-field and dioxins chemistry for incineration plants and experimental investigation.Waste Manage, 2000, 20(1):27
[25]	Wang X, Li Y J, Zhu T Y, et al.Simulation of the heterogeneous semi-dry flue gas desulfurization in a pilot CFB riser using the two-fluid model. Chem Eng J, 2015, 264:479
[29]	Kong M, Liu Q C, Wang X Q, et al. Performance impact and poisoning mechanism of arsenic over commercial V₂O₅-WO₃/TiO₂ SCR catalyst. Catal Commun, 2015, 72:121
[30]	Kwon D W, Park K H, Hong S C. Enhancement of SCR activity and SO₂ resistance on VO_x/TiO₂ catalyst by addition of molybdenum. Chem Eng J, 2016, 284:315
[31]	Zhao Y, Hao R L, Yuan B, et al. Simultaneous removal of SO₂, NO and Hg⁰ through an integrative process utilizing a cost-effective complex oxidant. J Hazard Mater, 2016, 301:74